ELECTRICIAN - AGRICULTURE--------------2016

 Paper Code:-  152/2016   Date Of Test:- 16.11.2016

1. Repulsion motor is provided with:

(A) Comnuitator (B) Centrifugal switch

(C) Capacitor (D) Squirrel cage rotor

2. Whenever a poly phase motor is loaded the:

(A) induced emf  in the rotor increases and its frequency falls

(B) induced emf in the rotor increases and its frequency rises

(C) induced in the rotor remains constant

(D) induced emf in the rotor decreases and its frequency increases

3. For three resistance are connected in three phase, the power consumed will be more in

connection.

(A) star delta (B) star (C) delta (D) delta -star

4. Synchronous motors run on leading power factor when connected in:

(A) under excitation (B) rated excitation

(C) fully loaded (D) over excitation

5. The out put voltage of a solar cell is approximately:

(A) 1.2 V (B) 0.5 V (C) 2.1  V (D) 3V

6. Slip rings are generally made  of;

(A) phosphor bronze (B) aluminum

(C) copper (0) carbon

7. The hydrometer reading of fully charged lead acid battery;

(A) 1.2 (13) 1.5 (C) 1.11 (D) 1.26

8. In  induction motor percentage slip is Maximum at:

(A) low speed (B) medium speed

(C) stand still condition (D) synchronous speed

9. Economiser is  a  part of:

(A) hydel  PS (B) nuclear  PS (C) thermal PS (D) diesel PS


10. The crawling in an induction motor is caused by:

(A) improper design of the machine (B) low voltage supply

(C) high load (D) harmonics developed in the motor

11. The commutator segments are placed in:

(A) rotor (B) stator (C) armature (D) field

12. Reduction in the capacitance of capacitor start motor results in reduced:

(A) noise (B) starting torque

(C) speed (D) armature reaction

13. In an ac circuit the ratio of klV/kVA represents:

(A) power factor (B) load factor (C) starting torque (D) diversity factor

14. The unit of inductance is:

(A) OHM (13) MHO (C) HENRY (D) FARAD

15. Ear to ear resistance of human body:

(A) 400 (13) 1 kilo ohms (C) 650 ohms (I)) 100 ohms

16. Centrifugal switches is provided for disconnecting the auxiliary winding in a:

(A) capacitor run motor (B) capacitor start motor

(C) reluctance motor (D) hysteresis motor

17. Transformer core is laminated to:

(A) reduce the copper loss (13) reduces the eddy current loss

(C) reduces the core loss (D) hysteresis loss

18. Which type of loss is not common to transformer and rotating  machines  7

(A) eddy current  loss (B) copper loss

(C) hysteresis loss (D) windage loss

19. The difference between the synchronous speed and the actual speed of an induction motor is

known as  :

(A) slip (B) regulation (C) black lash (D) lag

20. Three resistances of 30, 15, 5, ohms are connected th parallel, their combined resistance will

be:

(A) greater than 30 ohm (11) between 30 to 15 ohm

(C) less than 5 ohm (D) between 15 to 5 ohm

21. Which  of  the  following acts as a depolarizer M a dry cell?

(A) zinc chloride (B) carbon powder

(C) ammonium chloride (D) manganese dioxide

22. Efficiency  of  a  power  transformer is  of the  order  of:

(A) 50% (B) 7500 (C) 98% (0) 45%

23. The strongest diet -magnetic material:

(A) sulphur (B) bismuth (C) glass (13) graphite

24. The magnitude of torque developed by a three phase induction motor depends upon:

(A) rotor current, rotor emf. rotor pf

(B) supply voltage, stator current, frequency

(C) number  of poles, speed, frequency

(D) synchronous speed, rotor speed, frequency

25. Rheostat method of speed control of induction motor is used In:

(A) squirrel cage  LM  (B) slip ring INI (C) double cage

at (D) all of the above

26. In a three phase IM the number of poles in the rotor winding are:

(A) zero (B) less than stator poles

(C) equal  to stator poles (D) more than stator poles

A 5 152/2016

27. If the air gap of induction motor is increased:

(A) the magnetizing current will increase

(B) the pi will increase

(C) speed of the motor will increase

(D) friction and windage loss will increases

28. Isolate fire from the supply of oxygen by blanketing it with foam, sand etc.

(A) starving (B) cooling (C) spray water (D) smothering

29. What is the condition of ohm's law ?

(A) constant resistance (B) constant voltage

(C) constant current (D) constant temperature

30. Power pa

(A) energy/time (B) energy/voltage (C) current/voltage (D) time/voltage

31. Moving coil instruments are use:

(A) ac only (B) both ac/dc (C) tic only (D) none of these

32. Low resistance means:

(A) up to 10 ohm (B) 1 ohm and below

(C) 1000 ohm (D) 5(X)  ohm

33. Unit of resistivity:

(A) ohm (B) ohm -m (C) ohm m 2 (D) ohm/m

34. Kelvin bridge is used for measure:

(A) capacitance (B) low resistance

(C) inductance (D) insulation resistance

35. Resistivity of eureka at 211'C:

(A) 2.8 x  10-8 (B) 1.72  x 10-8 (C) 49 x 10-8 (D) 20.2 x 10 -8

36. Application of series parallel combination:

(A) current divider (B) maximum resistance

(C) power divider (D) voltage divider

37. An earthing electrode usually made of  :

(A) PVC pipe (B) carbon plate (C) glass rod (D) metal plate

38. The color of protective conductor:

(A) green- yellow (B) green - red (C) green - blue (D) green - black

39. The color of middle wire of 3 wire DC circuit is:

(A) red (B) black (C) blue (D) green

40. Example of primary cell:

(A) Lead acid cell (B) Edison cell (C) Voltaic cell (D) Nickel - iron cell

41. The  amp  -how efficiency of lead acid cell  :

(A) 750 (B) 90  -  95% (C) KO - 85% (D) 60 -  65%

42. High rate discharge tester consists of:

(A) low range ammeter (B) high range voltmeter

(C) low range voltmeter (D) high range ammeter

43. The color of fresh Silica gull  is:

(A) Blue (B) Red (C) Black (D) Light pink color

44. Imaginary line joining the two poles of a magnet:

(A) magnetic equator (B) magnetic pole

(C) magnetic lines (D) magnetic field

A 7 152/2016

45. Rotor copper loss of a three phase induction motor is:

(A) Fractional slip x input power to the rotor

(B) Fractional slip x output of the rotor

(C) Input power x output power

(I)) AU the above

46. 1 Metric horse power is:

(A) 742 W (B) 735 W (C) 735.6 W (D) 746 W

47. The back emf set up in the stator of a synchronous motor will depend on:

(A) rotor speed only (B) stator speed only

(C) rotor emf (D) rotor excitation

48. The armature 1Vcig of repulsion motor is excited:

(A) resistively (B) inductively (C) conductively (D) capacitively

49. The main disadvantage of shaded pole motor:

(A) low  starting torque (B) little over load capacity

(C) low efficiency (D) all the above

50. The armature flux opposes the main flux is  in  synchronous  machine when  the  PF  is:

(A) unity (13) zero lagging (C) zero  leading (D) 0.8 lagging

51. Dielectric strength  of a  medium is:

(A) Joules/m2 (B) Coulomb/ m2 (C) kV/ mm (D) Volt/m 2

52- Electric  intensity is expressed as:

(A) welter (B) Volt/m (C) einf (D) coulomb

53. Whenever  two charges are separated  there exist:

(A) magnetic field (B) electric field

(C) electrostatic  field (D) era

54. Potential inside  the  hollow charged  sphere:

(A) less than its surface (B) greater than on its surface

(C) same as on its surface (D) zero

55. Capacitance  in  any circuit is opposition to:

(A) voltage (B) current flow

(C) any change in current (D) any change in power

56. The  simple  measuring instrument used  to  transfer  measurement from the steel rule to

object:

(A) try -square (B) calliper (C) scriber (D) punch

57. 2 ohm resistance having  current  of 2  A will  dissipate the power of:

(A) SW (B) 81 (C) 2W (D) 4W

58. li the diameter of a wire is doubled keeping the length constant the resistance:

(A) becomes one fourth (B) become  twice

(C) remains  same (D) becomes 4 times

59. Which of the following is linear and bilateral element?

(A) Semiconductor (B) resistor (C) electron tube (D) transistor

60. Why accumulators  are  preferred  to  piny  cell  in  motor  car?

(A) they are bulk (B) they have high internal resistance

(C) they can be recharged (D) all  the above

61. Sedimentation occurs in lead acid cell to:

(A) over charging  at  high rate (B) over charging at slow rating

(C) no use for longer  period (D) slow charged rate

62. Kirchhoff's  law  are  valid for  :

(A) linear circuit (B) non-linear circuit

(C) both linear and non-linear circuit (D) passive circuit

63. The algebraic sum of all IR drops and ern( in any closed loop of  a network as  per KVL is:

(A) + ve (B) zero (C) —Ye (D) +ve or —ve

64. Form factor is the ratio of:

(A) average value/nns value (B) average value x tins value

(C) instantaneous  value/rms  value (D) nns  value/average  value

63. The power factor of the inductive load  is:

(A) leading (F) lagging (C) unity (D) zero

66. A  choke coil has:

(A) high inductive, high resistance (B) low  inductive, low  resistance

(C) low inductive, high resistance (D) high inductive,  low  resistance

67. A  choke is used for limiting current  in:

(A) AC  ckt only (B) DC ckt only

(C) both  AC and  DC (D) either  AC or DC

68. Impedance at series resonance circuit:

(A) maximum (B) average (C) minimum (D) all  the above

69. Power factor  is  defined as:

(A) kVA/kVAR (B) kVA/kW (C) kW/kVA (D) kW/kVR

70.  2 Wattmeter method  measuring power, 2 meters read equal  and  opposite reading the  load

power factor  :

(A) zero (B) 0.5 (C) unity (D) above 0.5

71. The secondary  current  of 400 kVA,  11kV/433V, 3 phase transformer is about:

(A) 420  A (B) 533  A (C) 666.5 A (D) 840 A

72. The current rating of  400 min2 AYFY cable is:

(A) 400A (B) 435A (C) 305A (D) 335A

73. The maximum efficiency of  distribution transformer  is:

(A) 1/4th load (B) fun  load (C) 3/4Ih load (D) half load

74. Unit of luminous intensity:

(A) lumen (B) lux (C) candela (0) lumen/m

75. The most efficient lamp:

(A) graphene (B) LED

(C) CFL (D) sodium vapour lamp

76. The larger transformer stepped core arrangement  is  used to minimize the use of:

(A) core (B) copper (C) hysteresis loss (D) core  loss

77. Examine the Commutator and  brushes:

(A) weekly maintenance ( 3) monthly  maintenance

(C) daily maintenance (D) yearly maintenance

78. In DC generator the voltage drop of copper -carbon brush is about:

(A) 1.6 V (B) 2 V (C) 1.75 V (D) 0.3 V

79. Alternator voltage regulation is  determined by emf method.  It  is due  to:

(A) Rothert (B) Behn-Eschenberg

(C) Faraday (0) Pointer

80. The starting torque of capacitor  start, capacitor  run is about:

(A) 200% of FL torque (B) 50% of  FL  torque

(C) 300% of FL torque (D) 100% of FL torque

A 11 152/2016

81. The first Director General of Archaeological Survey of India :

(A) Mountbatten (B) Alexander Cunningham

(C) Wheeler (D) Ernest Mackey

82. Name the first Indian to win the World Amateur Billiards Title.

(A) Wilson Jones (B) Kamaljit Sandhu

(C) Ravi Shastri (D) K. Malleswari

83. In  which place the Great Victoria Desert is located  ?

(A) Canada (B) Africa (C) Asia (D) Australia

84. Name  the  Kerala  ruler  who gave  his country  to Sri  Padmanabha as Tripadidana.

(A) Satan Tampuran (B) Swati Tirunal

(C) hfarthanda  Varma (D) Rama Varma

85. Who was known as Frontier Gandhi?

(A) Abdul Kalam And (B) NIuhammed Ighal

(C) Khan Abdul Ghafar  Khan (D) Patel

86. In which year Mountbatten Plan was announced in India?

(A) 1947 (B) 1946 (C) 1945 (D) 1948

87. Director of the film 'Tams" explaining about partition of India:

(A) Satyajit Rai (B) Govind Nihalani

(C) Mrinali Sen (D) Narain Bharati

88. In which  year Sadhujanaparipalanayogam established ?

(A) 1903 (B) 1905 (C) 1907 (D) 1910

89. Name the event which is related to Savona Jatha.

(A) Shartar Agitation (B) Quit India Movement

(c) Attingal Revolt (D) Vaikkom Satyagraha

90. What  is the  name of spice which  is  called as "Yavanapriya" ?

(A) Ginger (B) Pepper (C) Cinnamon (D) Cardamom

91. Who was the Vicemy of India during the time of Round Table Conferences?

(A) Lord Canning (B) Ramsay Mac Donald

(C) Lord Curzon (D) Lord Irvin

92. The First person who  offer  Irian, idual  Satyagraha  in Indian  Freedom  Movement:

(A) Vinobha Bhave (B) Dr. B.R. Ambedkar

(C) Vallabhbhai  Patel (D) Narendra Dutta

93. In Which  Year  Historic  Lahore session of Indian National Congress held?

(A) 1919 (B) 1929 (C) 1930 (D) 1942

94. Which is the Name of Commission sent  to India to  enquire about  the  work  of  Govt. of India

Act  of 1919?

(A) Cups Mission (B) Wardha Commission

(C) Simon Commission (ID) Cabinet Mission

95. Which is the birth place of Mar Kuriakose Eliias Chavara ?

(A) Bharanaganm (B) Mannanant (C) Mezhathur (D) Kainakari

96. Pattanam was situated in the banks of river

(B) Bharataputha (C) Periyar (D) Kurumali puzha (A) Pamba

97. The Yarkungzangbo river in India is known as

(A) Brahmaputra (B) Mahanadi (C) Kaveri (D) Sindhu

98. The Power to Prorogue the Lok Sabha rests with

(A) Speaker (B) President (C) Supreme Court (D) Prime minister

99. Who is the Founder of Samatwa Samaj ?

(A) Chattampi swatnikal (II) Ayyankali

(C) Vaghbhatananda (D) Vaikunda Swamikal

100. The Political Gum of Mahatma Gandhi:

(A) Gokhale (B) Tilak

(C) Surendra Nath Banerjee (D) Dadabhai Naoroji



Continue Reading →

ASSISTANT ENGINEER - DIRECT/BY TRANSFER - KERALA WATER AUTHORITY-----2016


Paper Code:- 28/2016   Date Of Test:-13.02.2016



Maximum: 100 marks

Time: 1 hour and 15 minutes

1. A triangle lamina having a base 1 in and height 1.5 in is placed vertically under water with

the base parallel to the water surface and the base below 3 m of water. The total force

exerted on one face is:

(A) 18.394 kN (B) 18.394 kg

(C) 36.788 kN • (D) 15.234 kg

2. If the velocity potential function is given by = 3x — 4y, find the magnitude and direction of

velocity at any point:

(A) 4.87 m/s, 450 (B) 5 m/s, 38° 3'

(C) 6m/s. 53° 7' (D) 7 mls, 61° 7'

3. A jet of water 40 mm in diameter has a velocity of 25 m/s. Find the power of the jet:

(A) 10.81 kW (B) 9.82 kW

(C) 10 kW (D) 4.35 kW

4. Find the bed slope 'i' of a wide rectangular channel so that the flow to reach a given critical

depth d, and Manning's coefficient n:

(A) i (B) i =—

dr

. gn2

(c) i=e 4 g i

d"3

5. The discharge available from a tube well is 120 mi/hr. Assuming 3200 h of working of the

tube well for a year, the intensity of irrigation as 50% and average depth of Rabi and Kharif

crop as 48 cm, the culturable area that this tube well can command is:

(A) 160 ha (B) 172 ha

(C) 168 ha (D) 80 ha

6. Lacey's formula for fixation of water way is:

(A) V ..0.55 y°54 (B) 4.75/

10 Q = KAI (D) Q =, AV

7. An offset is laid out 2° from its true direction on the field. If the scale of plotting is 10 in to

1 cm, find the maximum length of the offset so that the displacement of the point on the

paper may not exceed 0.25 mm?

(A) 5.0 m (B) 6.12 m

(C) 7.16m (I)) 8.16m

8. The following perpendicular offsets were taken at 10 m intervals from a survey line to an

irregular boundary line: 3.25, 5.6, 4.2, 6.65, 8.75, 6.2, 3.25,4.2, 5.65. Calculate the area by trapezoidal rule

(A) 433 m2 (B) 439.67 m2

(C) 424.44 m2 (D) 440m2

9. A square footing 2.5 m x 2.5 in is built in a homogeneous bed of sand of unit weight 20 kN/ni 3

and having an angle of shearing resistance of 36°. The depth of the base of the footing is

1.5 in below the ground surface. Calculate the safe load that can be carried by a footing with

a factor of safety 3 against complete shear failure?

Bearing capacity factors N, = 65.4, N g = 49.4 and N, 54.0

(A) 4325 kN (B) 4927.5 kN

(C) 5:319.6 kN (D) 5462.5 kN

10. Hydrophobic cement is obtained by grinding ordinary Portland cement clinker with:

(A) Hydrochloric acid (B) Oleic acid

(C) Glicerine (D) Acetol

11. How much initial slump is required for a concrete mix to he fluidised by plasticizers or super

plasticizers?

(A) 2 to 3 cm (B) 2 to 3 mm

(C) 5 cm (1)) 10 mm

12. ISO: 800-2007 limits the va lues of width- thickness ratios of the elements of a steel section to

place a check on:

(A) Bending buckling (B) Torsional buckling

(C) Flexural torsional buckling (1)) Local buckling

13. The shape factor of a square of side 'a' with its diagonal parallel to the ZZ axis is :

(A) 2 (B) 1.7

(C) 2.343 (D)

14. Strength of a 20 mm diameter bolt of grade 4.6 for a single cover butt joint. The cover plate

being 10 mm thick. Assume steel of grade Fe 410, f„ = 410 MPa, for bolts of grade 4.6,

= 400 MPa, Partial safety factor for the material of the bolt y„, t , = 1.25 and net tensile

stress area of 20 mm diameter bolt A„b = 245 mm2, le; =0.5 in single shear is:

(A) 80 kN (B). 45.26 kN

(C) 96.0 kN • (D) 125 1EN

15. Minimum grade of concrete mix used for water retaining structures with alternate wetting

and drying:

(A) M20 (B) M25

(C) M30 (D) M35

16. A hook 12 mm diameter is embedded in concrete for a distance of 100 mm. Calculate the

maximum load which the hook can carry if the bond stress is not to exceed 1.28 N/mm 2:

(A) 5100N (B) 415N

(C) 4825 N (D) 5000N

17. Year's purchase for an old building if its future life is 15 years and the rate of interest is 7%

on capital and 4% for sinking fund:

(A) 8.333 • (B) 9.231

(C) 10.11 (D) 10.21

18. A beam of span / carries a concentrated load P at mid span. Work done by the external load

Is:

P213 p218

(A) (111

48 El 96 E1

1,13 (C) (D)

96 El 48 E1

19. A three hinged arch of span 20 m and rise 4 m carries a uniformly distributed load of

25 kN/m. Horizontal thrust is:

(A) 250 kN (B) 600 kN

(C) 312.5 kN (D) 425 kN

20. Find the shortest length L for a pin ended steel column having a cross section of

60 ram x100 nim for which Euler's formula applies. Take Es 2 x 10$N/mm2 and critical

proportional limit is 250 N/mm 2: •

(A) 6000 mm (B) 2500 mm

(C) 2000 mm (D) 1639 mm

21. Which method of analysis of water distribution system is most suitable for long and narrow

pipe system?

(A) Circle method (B) Hardy Cross Method

(C) Equivalent Pipe method ' (D) Electrical Analysis method

22. For disinfecting water supply, it is required to treat 5,00,000 litres of daily supply with

0.5 ppm of chlorine. If the disinfectant is available in the form of bleaching powder containing

30% of available chlorine, the amount of bleaching powder required to treat the, daily flow of

water is:

(A) 0.833 kg (B). 0.916 kg

(C) 0.918 kg (D) None

23. In water treatment settling unit, water having a temperature of 20 Degree Centigrade

carries solid particles with average diameter of 0.05 mm and specific gravity 1.20. Given

y = 1.01 centi stokes. Settling velocity of settling particles is:

(A) 0.027 cm/s (B) 3.1 mm/s

(C) 2.73 cm/s (D) 0.21 minis

24. A main sewer is to be designed to receive a flow from 1 lan 2 area of a community where the

population density is 200 persons/ha. The average sewage flow is 150 litres per capita

per day. Assume peak factor ='3. The design flow for the main sewer is:

(A) 7.934 mlpd (B) 8.13 mlpd

(C) 10.0 mlpd (D) 9.0 mlpd

• 25. At shut off head of a centrifugal pump, the discharge is:

(A) Maximum (B) Zero

(C) Rated Discharge (D) None

26. The minimum dissolved oxygen which should always be present in water in order to save

aquatic life is:

(A) 1 ppm • (B) 40 ppm

(C) 4 PPm (D) 10 ppm

27. In the case of surface water with a pH range of 6 to 8, which is the most suitable coagulant:

(A) Alum (B) Quick lime

(C) Lime (D) Potassium Permanganate

28. The pipe joint commonly used in pumping station are:

(A) Flexible joint (B) Expansion joint

(C) Flanged joint (D) Socket and spigot joint

29. The strength of chlorine in fresh bleaching powder is:

(A) About 60% (B) About 10%

(C) About 20% (D) About 30%

30. Estimated the quantity of secondary sludge produced by a secondary settling tank treating

sewage discharge of 3.5 mid. The sludge may be assumed to have a solid concentration of

200 mg/I, removal efficiency of suspended solids as 90% and the solid content of the sludge as

6 per cent :

(A) 10.5 cum/day •

(B) 8.3 cum/day

(C) 9.1 cum/day

(D) 7.93 cum/day

81. The equation used for experimental measurement of viscosity is:

(A) Darcy equation (B) Stokes equation

(C) Fanning equation (D) Hagen Poiseuille equation

32. Bernoullis equation is derived starting from:

(A) Mass Balance (B) Force Balance

(C) Momentum Balance (D) Energy Balance

38. Orifieemeter is used for measuring:

(A) Pressure (B) Flow rate

(C) Density (D) Viscosity

34. Optical Pyrometer working principle is based on:

(A) Stefan -Boltzmann law (B) Weins displacement law

(C) Kirchoff law (D) Planck& law

35. Fronde number is directly proportional to:

(A) Impeller speed (B) Fluid viscosity

(C) Square of Impeller diameter (D) Square of impeller speed

36. Centrifuging in Ball mills occur when the speed is:

(A) Equal to Critical speed (B) Less than critical speed

(C) Greater than critical speed (B) None of the above

37. Peclet Number NPe is the product of:

(A) Reynolds Number and Nusselt Number

(B) Reynolds No. and Prandtl No.

(C) Prandtl No. and Nusselt No.

(D) Reynolds No. and Rayleigh No.

38. LMTD correction factors are used for:

(A) Parallel flow (B) Counter Flow

. (C) Cross flow (D) All the above three

39. Slugging in fluidized beds occur when:

(A) Particles are large and heavy

(B) The Vessel is narrow and the bed is deep

(C) Neither (A) nor (13)

(D) Both (A) and (B)

40. Michaelis - Menten parameters can be evaluated using:

(A) Eadie Hoftsee Plot (B) Lineweaver Burke Plot

(C) Neither (A) nor (B) (D) Both (A) and (B)

41. In the CGS system 1 stoke is defined as:

(A) 1 ft2/s (B) 1 ne I s

(C) 1 ire/s (D) 1 cne I s

42. Boiling Point Elevation of solutions strongly influences:

(A) Capacity of multiple effect evaporators

(B) Economy of multiple effect evaporators

(C) Both capacity and economy

(D) Neither capacity nor economy

43. At all humidities Other than zero or hundred percentage, percentage humidity is:

(A) Greater than relative humidity (B) Equal to relative humidity

(C) Less than relative humidity • (D) None of the above

44. Many important fermentation products like antibiotics are formed during:

(A) Lag phase (B) Growth phase

(C) Stationary phase (D) Death phase of cell growth

46. Dilution rate D for a bioreactor is the reciprocal of:

(A) Space Time (B) Residence Time

(C) Space velocity (D) Time constant

46. Ficks law of diffusion is analogous to :

(A) Newtons law of viscosity (B) Fouriers law of heat conduction

(C) Both (A) and (B) (D) Neither (A) nor (B)

47. Temperature dependency of equilibrium constant is predicted by:

(A) Vant Hoff Equation (B) Clayperon Equation

(C) Raoults law (D) Arrhenius Equation

48. In an ideal PPR, the reactant concentration:

(A) is uniform within the reactor

(B) varies along the cross section of the reactor

(C) varies along the length of the reactor

(D) none of the above

49. Baffles in shell and Tube heat exchangers are provided mainly for:

(A) Increasing shell side turbulence (B) Increasing tube side turbulence

(C) Fixing the tubes (I)) Fixing the tie rods .

50. Conversions in reversible exothermic reactions can be improved by:

(A) Interstage Heating (B) Interstage Cooling

(C) Isothermal Operation (D) Isobaric operations

51. Fmssling correlation relates mass transfer coefficient with:

(A) Particle size (B) Particle velosity

(C) Mass diffusivity (D) All the above three

52. Knudsen diffusivity is:

(A) Directly proportional to pressure

(B) Independent of pressure

(C) Proportional to square root of pressure

(D) Inversely proportional to pressure

53. Crushing Rolls are:

(A). Primary crushers (D) Grinders

(C) Ultrafine grinders • (D) None of the above

54. Differential method of analysis of kinetic data is:

(A) Complex but accurate (B) Simple and accurate

(C) Complex and inaccurate (D) Simple and inaccurate

55. Rate Selectivity parameter is important in the designof:

(A) Multiple reactions (B) Single reactions

.(C) Elementary reactions (1)) None of the above

56. A U-tube manometer is connected to a vessel to measure the pressure inside. If mercury is

the working fluid of manometer, the height difference between two columns of the

manometer measured is 24 cm, the pressure inside the vessel in kPa is:

(A) 31.9 (B) 49.1

(C) 3.1 (D) 10.4

57. One kilogram of water is heated from 20°C to 90°C. If the specific heat of water is

4.186 kJ/kgK, the entropy change occurred assuming constant specific heat in kJ/kg1{ :

(A) 0.0786 (B) 9.5321

(C) 98.1773 (D) 0.8958

58. The volume flow rate of a water jet striking a flat plate placed normal to its path is 0.06 m 3/s

and exerts a force of 935 N. Considering the density of water as 1000 Kg/m 3 , the diameter in

mm of the water jet is:

(A) 46 (B) 70

(C) 38 CD) 97

59. In order to have maximum power from a Pelton turbine, the bucket speed must be:

(A) Equal to the jet speed (B) Equal to half the jet speed

(C) Equal to twice the jet speed (D) Independent of the jet speed

60. Heat and work are:

(A) Path functions (B) Extensive properties

(C) Point functions (D) Intensive properties

61. Air at 20°C blows over a hot plate of dimensions 50 x 60 cm maintained at 250°C. If the

convection heat transfer coefficient is 29 W/m2 °C, the heat transfer took place in kW is:

(A) 36.6 (B) 14

(C) 8 (D) 2

62. In a condenser of a power plant, the steam condenses at a temperature of 70°C. The cooling

water enters at 30°C and leaves at 50°C. The logarithmic mean temperature difference of the

condenser is:

(A) 24.2°C (B) 28.8°C

(C) 20.6°C (D) 37.5°C

63. The work done in kJ/kg to pump water isentropically from 100 KPa and 30°C to 5 MPa at a

constant specific volume of 0.001021 m 3 /kg neglecting the changes in kinetic energy and

potential energy is:

(A) 5 (B) 38

(C) 232 (D) 84

64. A refrigerator takes an electrical power of 150 Watts and rejects 450 Watts to surrounding

air. The coefficient of performance of refrigerator is:

(A) 1-2 (B) 0.8

(C) 3 (D) 2

65. Which one of the following is a CPC refrigerant?

(A) R744 (B) R290

(C) R502 (D) R718

66. Tooth interference in an external involute spur gear pair can be reduced by:

(A) Decreasing center distance between gear pair

(B) Increasing pressure angle

(C) Decreasing module

(D) Decreasing number of gear teeth

67. The following data refers to two crossed helical gears used for speed reduction. Gear 1: Pitch

circle diameter in the plane of rotation 80 mm and helix angle 30°. Gear H: Pitch circle

diameter in the plane of rotation 120 mm and helix angle 22.5°. If the input speed is

1280 rpm, the output speed in rpm is:

(A) 900 rpm (B) 950 rpm

(C) 800 rpm (D) 850 rpm

68. A clutch has outer and inner diameters 100 mm and 40 mm respectively. Assuming a

uniform pressure of 2 MPa and coefficient of friction of liner material 0.4, the torque carrying

capacity of clutch is:

(A) 148 Nm (B) 490 Nm

(C) 372 Nm (D) 196 Nm

69. If the equilibrium speed of a governor is constant for all radii of rotation of the fly balls

within the working range, it is known as:

(A) Isochronism (B) Hunting

(C) Insensitiveness (D) Stability

70. The gyroscopic couple of a suspended disc rotating at 1000 rpm is 15 N -m and the moment of

inertia is 0.4 kg -ms, then the precession velocity of the disc in red/sec is close to:

(A) 0.35 (3) 35

(C) 8.5 (D) 0.0375

71. The fraction of unbalanced mass used for primary balancing of a reciprocating engine is:

(A) 0.2 (B) 0.9

(C) 0.6 (D) 0.05

72. If the balancing mass of a locomotive wheel is 15 kg acting at a radius of 0.7 in when the

wheel has dead weight of 110 kg, the limiting rotational speed of the wheel in rad/sec to avoid

lifting from rails is close to:

(A) 7.1 (B) 6.6

(C) 9.7 (D) 8.4

73. The crystal structure of austenite is:

(A) Body centered cubic (B) Face centered cubic

(C) Hexagonal closed packed (D) Body centered tetragonal

74. The maximum energy that can be absorbed per unit volume without creating a permanent

distortion in a material is known as:

(A) Modulus of resilience (B) Modulus of toughness

(C) Modulus of rupture (D) Modulus of rigidity

75. A stainless steel rod of 10 mm diameter id being reduced to 9 mm by turning on H lathe. If

the spindle rotates at 360 rpm and the tool travel rate is 175 mm/min, the material removal

rate in mm3/min is close to:

(A) 1034.6 (B) 2610.8

(C) 874.4 (D) 356.9

76. The welding processes which uses non -consumable electrode is:

(A) Gas metal arc welding (B) Submerged arc welding

(C) Gas tungsten arc welding (D) Flux coated are welding

77. Internal gear cutting operation can be performed by:

(A) Milling (B) Bobbing

(C) Shaping with pinion cutter (D) Shaping with rack cutter

78. For a damped vibrating system, when the critical damping coefficient is less than the

damping coefficient, the system is said to be:

(A) Under -damped (B) Over -damped

(C) Critically -damped (D) Undamped

79. If two nodes are observed at a frequency of 1200 rpm during whirling of a simply supported

long slender rotating shaft, the first critical speed of the shaft in rpm is.

(A) 1800 (B) 400

(C) 600 (D) 2400

80. A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is

increased by 1%, with the internal pressure remaining the same, the percentage change in

the hoop stress is.

(A) 1 (B) 1.25

(C) 3 (D) 2

81. Who was the President of Indian Constituent Assembly?

(A) Dr. B.R. Ambedkar (B) Jawaharlal Nehru

(C) Dr. Rajendra Prasad (1)) Sardar Patel

82. The first amendment of Indian Constitution came into force on:

(A) 18-6-1951 (B) 18-6-1952

(C) 18-6-1953 (D) 28-8-1954

83. In the Parliamentary system of India, the executive is subordinated to:

(A) The voters (B) Legislature

(C) Media (1)) None of these

84. Who is the founder of PRDS?

(A) K.P. Yohannan (B) Poykayil Srikumara Devlin

(C) Chattamby Swamy (D) Sabodaran Ayyappan

85. Who helped the Vaikom Satyagrahis by opening a free kitchen for them?

(A) Bengalis • (B) Assamese

(C) Akalis (1)) Kashmiris •

86. The women K.P.C.C. President who lead the Quit India and Civil disobedience movements:

(A) Fathima Tleevi (B) Kutty Malu Amma

(C) Nafeesath Beevi (1)) Captain Laxmi

87. The author of the work 'Odakkuzhal' who won the 'Njanapeetom' Award:

(A) Ulloor (B) Vallalhol

(C) G. Sankara Kurup (D) Akkithom

88. Who was the leader to become the head of the Radio Broadcast division , of Indian

Independent League?

(A) K. Kelappan (B) T.K- Madhavan

(C) K.P. Kesava Menon (D) Vakkom Moulavi

89. Who visited Mahathma Gandhi at Thirunelvely in 1921:

(A) Kumaran Man (B) Sree Narayana Guru

(C) T.K. Madhavan (I)) KY. Kesava Menon

90. Where was the first SNDP meeting convened? ,

(A) Aluva (B) Varkala

(C) Pallana (B) Aruvippuriun

91. Birth place of Saint Kusiako Elias Chavara :

(A) Kandankasy (B) Chennamparampu

(C) Kainakary (B) Mannanam

92. Which Newspaper was founded by Vakkom Moulavi?

(A) Deshahhimanv (B) Swadeshabhimani

(C) Samvad Kaumudi (D) Mathrubhoomi

93. Kumaran Man's Veena Poovu was first published in:

(A) Flhashaposhini (B) Mangalodayam

(C) Nasrani Deepika (D) Prabhatham

94. Malayali Memorial Memorandum was submitted to:

(A) Sree Moolam Thirunal (B) Sree Ayilyam Thirunal

(C) Sree Avittam Thirunal (D) Sree Chit hira Thirunal

95. Which one is not a work of Changampuzha?

(A) Ramanan (B) Rakthapuhspangal

(C) Kilikonchal (D) Mayookhamala

96. The Historic struggle lead by Chattampy swamikal to join scheduled class students to

government schools occurred in which place:

(A) Olakettiyambalam (B) Ooruttambalam

(C) Vellayambalam (D) Vazhiyambalam

97. How many members are there in the Kerala legislative assembly?

(A) 140 (B) 141

(C) 142 (D)• 143

98. What is the percentage of seats reserved for women in the Kerala local self government

elections?

(A) 33 (13) 40

(C) 50 (D) 25

99. Who founded the first college in Kerala?

(A) S.N.D.P. (B) N.S.S.

(C) M.E.S. (D) CMS.

100. Mannathu Padmanabhan was the president of which Devaswom board?

(A) Travancore (B) Malabar

(C) Guruvayoor (D) None of the above

028/2016 14 A




Continue Reading →

ASSISTANT ENGINEER - ELECTRICAL - HARBOUR ENGINEERING -----2016

 

Paper Code:- 30/2016   Date Of Test:-17.02.2016



Maximum: 100 marks

Time : 1 hour and 15 minutes

1. Three resistances each having a value of a Ohm are connected to form a Y structure. If a

3 phase balanced supply with a line voltage of A volts is applied, then the power drawn per

phase from the supply is:

(A) A2/ 3a . (B) 3A2/ a

(C) A2 /a (D) None of the above

2. A 230V:50Hz, 10 supply is connected to the series combination of a pure resistance of 500 a

pure variable capacitor of 2511, and a pure variable inductor of 1.5mII. By properly

adjusting the component values, it is made that the current through the circuit is maximum.

What is the power factor of the circuit now?

(A) 0.866 (B) 0.5

(C) Zero (D) 1

3. In 30 power measurement using 2 Wattmeter method, both the Wattmeters are reading

positive and equal. This is becatise :

(A) The load is purely resistive (B) The load power factor is 0.5

(C) The phase sequence is RBY (D) The load is purely capacitive

4. A dc source of EMI? E Volts and internal Resistance, R Ohms is connected to a variable load

and it is adjusted such that the load abstracts maximum power from the source. The current

drawn from the source is:

(A) 4E/R (B) 2E2/R

(C) E/R (1)) E/2R

5. The minimum number of NAND gates required to implement a NOR gate is:

(A) 1 (B) 2

(C) S (D) none of the above

6. If A and B are boolean variables, the bcolean expression A+ AB is:

(A) 0 (B)

(C) 1 (D) A

7. Which one among Aluminum, Constantantan Mercury, Carbon have highest resistivity:

(A) Aluminum (B) Constantantan

(C) Mercury (D) Carbon

8. For a two terminal device, resistance decreases when the temperature increases, the

device is:

(A) made up of a metal (B) a semiconductor

(C) a dielectric (D) none of the above

9. Which one among the following has 2 fully stable states?

(A) Astable multivibrator (B) Sweep generator

(C) Flipflop (D) None of the above

10. In a hydro electric generation system, pressure variations due to rapid changes in velocity of

water is mitigated using:

(A) Tailrace pipe (B) Penstock

(C) Surge tank (D) None of the above

11. In a complex network containing active voltage sources with zero internal resistances and

linear bilateral elements the open circuit voltage across 2 terminals is 2W and the resistance

of the network viewed from the open circuited terminal is 6.250. If an eqivalent circuit

comprising of only a current source and impedance is made, the current source rating is:

(A) 25A (B) 6.25A

(C) 12.5A (D) 4A

12. A three phase balanced delta connected load of 5 + j6 Ohm in each phase is connected to a

line voltage of 40W is drawing a current from the supply. If another delta connected load of

same nature and magnitude is connected in parallel, the line current drawn from the supply

becomes:

(A) Double (B) Four times

(C) Less than half (D) One fourth

13. In an synchronous generator, selective elimination of odd harmonics can be done by:

• (A) Distribution of winding . (B) Symmetrical winding

(C) Short coding of winding (D) None of these

14. The surface integral of the normal component of Electric Field Intensity over a closed surface

is equal to 1 times the total charge inside it. This is the statement of:

C,

(A) Gauss's Theorem (B) Stoke' a Theorem

(C) Maxwell's Theorem (D) Poisson's Theorem

15. Smooth cylindrical type rotors with less diameter and large axial length are used for

Synchronous generators driven by:

(A) Water turbines (B) Radial turbines

(C) Steam turbines (D) None of the above

16. If the number of poles in a syncronous machine is 6, a slot angle of 10° mechanical, when

expressed in electrical degrees is:

(A) 60 (B) 20

(C) 30 (D) 15

17. If the number of turns of an inductive coil is doubled and core length is quadrupled, other

parameters being the same, the inductance of the coil became:

(A) doubled (II) halved

(C) quadrupled (D) unchanged

18. Which one among the following is TRUE regarding the selection of working flux density in

transformer design?

(A) High flux density in the core results into the reduction in Core loss '

(B) High flux density in the core results into an increase in Popper loss

(C) High flux density in the core results into high all day efficiency

(D) High flux density in the core results into saving in cost of iron

19. If the ratio of average charge voltage to average discharge voltage in a lead acid cell is 4/3,

the ratio of its Watt Hour efficiency to Ampere hour efficiency is;

(A) 0.75 (B) 413

(C) 16/9 (1)) None of the above

20. A three phase induction motor runs at 2% slip and its rotor frequency is 1Hz. Stator

frequency in Hertz is: .

(A) 60 (B) 50

(C) 40 (D) 20

21. To have a smooth, quite running of an induction motor by reducing humming and to prevent

cogging, the technique used is called:

(A) Damping (B) Concentrating

(C) Skewing (D) None of the above

22. If the flux per pole of a shunt-wound DC generator is halved and the number of poles is

doubled, the generated e.m.f. at constant speed:

(A) remains the same (13) doubled

(C) is halved (D) none of the above

23. In dc generators, the winding used in a machine delivering low voltage, high current

load is:

(A) progressive simplex wave winding (B) lap winding

(C) any type of wave winding (D) any of the above

24. Which among the following can support a synchronous motor in Starting.:

(A) Damper winding (B) Frequency divider

(C) Interpole (D) All the above

25. Two reaction theory is used in the analysis of Synchronous machine to take into account the;

(A) Difference in the number of poles in stator and rotor

or a Cylindrical pole

in achine

(B) Non uniformity of air gap between stator and rotor of a salient pole machine

(C) Non uniformity of air gap between stator and rotor of a cylindrical pole machine

(D) Difference in the number of poles in stator and rotor of a salient pole machine

26. In a transformer delivering a variable load, Zero voltage regulation can occur at:

(A) 0.45 lagging power factor load (B) unity power factor load

(C) 0.8 lagging power factor load (D) 0.7 leading power factor load

27. In an alternating voltage supply of constant voltage feeding a Transformer, the presence of

higher order harmonics can cause significant changes in: •

(A) Copper losses. (B) Regulation

(C) Core losses (D) • All of the above

28. The Maximum percentage efficiency of a 11(VA transformer with iron losses equal to 125 W

at upf load is:

(A) 90 (B) 72

(C) 60 (D) 80

29. Which among the following logic families are fastest in operation?

(A) ECL (B) TTL

(C) ,CMOS (D) DTL

30. De Morgan's Law says:

(A) NOR Gate is NOTed AND Gate (B) NAND Gate is NOTed OR Gate

(C) Both (A) and (B) above (1)) None of the above

31. Which of the following is/are the features of an Asynchronous counter?

(A) The same clock ptilses are applied to all the constituent Flip flops at a time

(B) Outputs of the flip flop are connected to the inputs of the very next flip flop

(C) Propagation delay limits the speed of operation

(D) None of the above

32. Which one of the following is fully CORRECF regarding 8085 microprocessor?

(A) It does not support handshaking in I/O operations

(3) It has only 6 flags

(C) It supports queue

(D) It has hardware and software interrupts

33. Which among the following is TRUE about an 8086 microprocessor?

(A) Its address and data bus are multiplexed

(13) Its accumulator size is 32 bit

(C) It supports the queue/pipelining feature

(I)) It does not have Master and Slave Mode operations

34. The excess -3 code corresponding to decimal number 156 is:

(A) 100010001010 (II) 010010110011

(C) 010010001001 (I)) None of the above

35. A Mod -31 synchronous Counter ideally has number of flipflops.

(A) 6 (B) 3

(C) 4 (D) 5

36. Which among the following Ware TRUE regarding the OP AMP circuit?

(A) Voltage follower employees positive feedback

(B) Integrator amplifies noise

(C) In Differentiator, gain is increased with an increase in frequency

(1)) Adder always have an attenuation

37. When comparing Active and Passive filters, which of the following statements are Wrong?

(A) Active filters require power source(s)

(B) Active filters have high input impedance •

(C) Active filters have low output impedance

(I)) All the above are correct

38. For tunpolar operation. an 8 bit Digital to Analog Converter has a resolution of:

(A) 128 (B) 256

(C) 64 (1)) Given data insufficient

39. In a circuit containing a transistor, both of its junctions are forward biased. It operates

in region.

(A) Cut off (B) Saturation

(C) Active (D) Pinch off

40. Number of valance electrons in Germanium is:

(A) 2 (3) 5

(C) 6 (I)) 4

41. The Switched Mode Power Supplies have higher energy efficiency compared to Linear Power

Supplies because:

(A) it uses isolation transformers

(B) it has devices with large space charge capacitance

(C) it does not work in active region

(D) it has high switching frequency

42. Gain of an amplifier can be stabilized by:

(A) Employing Positive feedback • (B) Employing Negative feedback

(C) Proper dc bias (D) Proper dc isolation

43. If only 5 bites are used for addressing the memory of a computer system, the memory

size is:

(A) 64 (B) 128

(C) 32 (D) 256

44. The ripple factor and efficiency of a half wave rectifier are respectively:

(A) 1.21 and 81.2% (B) 1.21 and 40.6%

(C) 0.482 and 81.2% (D) 0.482 and 40.6%

45. For a short transmission with series impedance Z, all the capacitances being negligibly small,

the ABCD constants of the line are:

(A) A r-1,B=Z,C=0,D=1 (B) A=Z,B=1,C=1,D=0

(C) A -1,B=0,C=2,D=1 (D) ,A.,Z,B=1,C=0,D=1/Z

46. The load flow analysis algorithm having the least rate of convergence is:

(A) Newton Raphson Method (B) Fast Decoupled Load -Flow Method

(C) Gauss Seidel Method (D) None of the above

47. The Opposition to the flow of current in a conductor can increase in *alternating circuits

compared to dc circuits due to :

(A) Proximity effect (B) Skin effect

(C) Ferranti effect (D) (A) and (B) above

48. What is meant by a flat line or Infinite line?

(A) Line open circuited

(B) Line with surge impedance equals the characteristic impedance

(C) Line terminated with charesteric impedance

(D) Line through which Power transmitted is high

49. Which one among the following is a method for equalizing the potential across the various

units of a string insulator?

(A) Usage of smaller cross arm (B) Usage of step grading

(C) Dynamic sheilding (I)) All of the above

50. Under ground cables are less preferable in high voltage transmission because of:

(A) poor insulation (B) high charging current"

(C) safety (D) none of the above

51. The metals normally used in a IIRC fuse are:

(A) Tin and lead (B) Tin and Silver

(C) Aluminium and lead (D) Aluminium and Copper

52. The transient stability of a power system can be improved by:

(A) Using rotor of lower Moment of Inertia for generator

(B) Using parallel lines

(C) Using low system voltage

(D) None of the above

58. For economic load dispatch:

(A) Incremental efficiency of each machine should be same

(B) Incremental production cost of each machine should be same

(C) Incremental fuel cost of each machine should be same

()) None of the above.

54. In a power system, the cost of generated electrical enegry will be low if:

(A) both load factor and diversity factor are low

(B) both load factor and diversity factor are high

(C) Load factor high. Diversity factor low

(D) Load factor low, Diversity factor high

56. An over exited synchronous machine has a lagging powerfactor. The machine is:

(A) Motoring (B) Generating

(C) Floating (D) Can be Generating or motoring

56. Which among the following is/are CORRECT about an RC phase shift oscillator?

(A) The RC network provides a phase shift of 180°

(B) It makes use of positive feedback

(C) Loop gain of the oscillator is almost one

(I)) All the above

57. In class B operation of power amplifiers, the collector current flows for:

(A) Less than a quarter of a cycle (B) The whole cycle

(C) Half the cycle (D) Less than half a cycle

58. For the characteristic equation 2S4 + S3 + 332 +5s +10 a 0, the number of roots in the loft

half S plane is :

(A) 2 03) 1

(C) 3 4D)(

59. The unity negative feedback system with GMS

)a- „ (10s+ 0

i oscillates at 2rad/s only

V- +Etasa-4k)

when:

(A) k = 1 (B) k = 2 and a =1

(C) k = 1 and a =2 (D) a=2

60. The steady state error of a negative feedback system with forward path gain function

5

-1--c and feedback path gain function HO= for a unit step input is

(S+) (S +

given by:

(A) infinity (B) zero

(C) 0.25 (D) 10%

61. The ratio of total power in the Amplitude modulated wave to the unmodulated carrier power

when the modulation index is 'in'

(A) I +2m2 (B) 1+ 0.5,1,2

(C) 1+ m2 (D) None of the above

62. The voltage across a load element is 40Z-15 and the current through the element is

2.5Z -30. The circuit powerfactor is:

(A) Lagging (B) Leading

(C) Unity (D) Data insufficient

63. 100 numbers of H2 linear bilateral resistances are connected in parallel and the combination

is fed by a WA constant current source. The power delivered by the source is:

(A) 10W (11) 1 W

(C) 100 W (D) W

64. Referring to a power plant, the term hot reserve refers to:

(A) Reserve generating capacity not in service, but in operation

(B) Reserve generating capacity not in service, but available

(C) Reserve generating capacity in service, but not in operation

(D) All the above

65. Power supply used for dielectric heating will normally have a frequency in the range:

(A) 1 to 5 kHz (B) I to 5 MHz

(C) 10 to 50 MHz (D) 10 to 50 kHz

66. As per Kelvin's Law, the most economical 817.0 of conductor is that for which:

(A) The variable part of the annual charges is equal to the St of annual energy

losses

(B) The constant part of the annual charges is equal to the cost of energy losses per

year

(C) The variable part of the energy charges is equal to the cost of annual energy losses

(D) The constant part of the energy charges is equal to the cost of annual energy

losses

67. Output voltage of a simple ideal buck type dc -dc converter working in continuous current

mode with an input voltage of 12V and turn ON time 5ms and switching frequency 501Iz is:

(A) 6V (B) —6V

(C) 3V (D) —3V

68. A power electronic circuit which can give a 2.5V, 30Hz output wave from a supply of 5V,

60Hz supply is:

(A) Voltage Source Converter (B) Cyclo converter

(C) Flyback Conveter (1)) None of the above

69. In a power electronic circuit, a free wheeling diode is used across a de load to:

(A) Reduce output voltage ripple

(B) Prevent reversal of load voltage

(C) Control output current ripple

(D) All of the above

70. Ten, 15V batteries each having an internal resistance of 30 are connected in series such that

one is aiding the others. Its Norton's equivalent circuit has:

(A) A current source of 0.5A and parallel resistance of 30

(B) A current source of 5A and parallel resistance of 301)

(C) A current source of 2.5A and parallel resistance of 300

(D) None of the above

71. The value of specific gravity of a lead acid battery under fully cargod condition is

approximately:

(A) 1.21 • (B) 2

(C) 2.8 (I)) None of the above

72. Which one of the following is equal to one ampere of current?

(A) Siemens/second (B) Watt/second

(C) Joule/second (D) Coulomb/second

73. An Ammeter is found to have a cramped scale. This is because:

(A) it employees eddy current damping

(B) it has spring control

(C) its deflecting torque has a nonlinear variation with respect to current

(D) of both (B) and (C)

74. Of the power electronic circuits, circuit employing Power MOSFETa has a higher switching

frequency because:

(A) MOSFET is a majority carrier device

(B) MOSFET has high input impedance

(C)MOSFET has insulated rate

(D) MOSFET has low signal to noise ratio

75. A measure of repeatability of measurement of a quantity is:

(A) Precision (B) Accuracy

(C) Significant (D) None of the above

76. The analogous electrical circuit quantity corresponding to the magnetic circuit quantity,

permeability is:

(A) Conductivity (B) Resistivity

(C) Susceptibility (D) None of the above

77. In load flow analysis the role of a slack bus is:

(A) as the reference bus

(B) as a bus which can absorb and gives out active power

(C) as a bus which can absorb and gives out reactive power

(D) all of the above

78. Rotation of a Rotating Induction Type Mechanical Energy Meter under no load condition can

. be reduced by:

(A) Copper shading bands (B) Compensating coils

(C) Eddy current damping (D) Drilling holes in the disc

79. The needle of a MI Ammeter oscillates around a central value. It may be due to poor:

(A) Damping torque (B) Controlling torque

(C) Deflecting torque (D) None of the above

80. The range of an Ammeter is to be extended from 250 mA to 2A. If the 250 mA meter has an

internal resistance of 100, what is the approximate value of the shunt resistance required to

extend the range:

(A) L430 (B) 2.50

(C) 50 (I)) 3.50

81. Time taken by the Constituent Assembly to prepare Constitution is?

(A) 2 years 10 Months 8 days (B) 2 years 11 Months 17 days

(C) 2 years 10 Months 17 days (D) 2 years 11 Months 18 days

82. In India Fundamental duties are adopted from:

(A) UK Constitution (B) USA Constitution

(C) USSR Constitution (D) German Constitution

83. Who is the author of Ente Gurunathan?

(A) Vallthol Narayana Menon (B) G Sankara Karim

(C) Kumaranasan (D) Poonthanam

84. The place where Ayyankali started a school for depressed classes?

(A) Neyyatinkara (B) Varkala

(C) Ulloor (D) Vengannoor

85. Who started the News Paper 'Mithavade in 1907?

(A) Moorkoth Kumaran (B) Vakkom Moulavi

(C) Dr Palpu (D) Theruvath Raman

86. Who wrote Sahithya Vicharam'?

(A) Joseph Mundassery (B) Kesava Dev

(C) KC Kesava Pillai • (D) M.P. Poul

87. How many people signed in 'Ezhava Memorial'?

(A) 10028 (B) 13716

(C) 13176 (D) 100001

88. 'Jathy Kummy' which criticized the prevailing caste sy stem was written by:

(A) 1' K Madhavan (B) Pandit Karuppan

(C) K P Vellon (D) Abraham Malpan

89. Who introduced the 'Subsidiary Alliance System'?

(A) Warren Hastings (B) Lord Lytton

(C) Lord Wellesly (D) Lord Curzon

90. The national Anthem of India 'Jana gana Mana' was first sung at:

(A) Calcutta 1911 (B) Delhi 1912

(C) Mumbai 1913 (D) Lahore 1919

91. Who is known as 'Kerala Kalidasan'? •

(A) A R Raja Raja Varma

(B) Raja Ravi Varma

(C) Kerala Varma Valiya Koil Thampuran

(D) Kodungaloor Kunjikuttan Thampuran

92. 'Oru Therlivinte Kadha' was written by:

(A) Ponkunnam Varkey (B) S K Pottakkad

Vaikkam Muhammad Basheer (I)) Thakazhy Sivasankara Pillai

93. Who was the first Indian to be elected to the British parliament?

(A) Gopala Krishna Ghokliale • (B) Mettilal Nehru

(C) TIalaGangadhara Thilak (I)) Dadabhai Naoroji

94. The great Victoria Desert is located in:

(A) Africa (B) Europe

(C) Australia (D) North America

95. Ajanta Caves are located in the state of:

(A) Gujarat (B) Orissa

(C) Maharastra (D) Karnataka

96. At which place Gauthama Buddha delivered his first sermon?

(A) Lumbini (B) Magadha

(C) Vaisaly ,(D) Saranath

97. In which of the following states does 16th National Women Boxing Championship take place?

(A) Meghalaya (B) Assam

(C) Orissa (D) Maharastra

98. Who has been elected as the first male member of national Commission for women?

(A) Alok Itawat (B) Chethan Bhagat

(C) Sudeep Nagarkar (I)) Kailash Satyarthy

99. Who has won the Nobel Prize 2015.in Literature?

(A) Patrick Modiano (B) Youyou Tu

(C) Svetlana Alexievich (D) Joseph William

100. World Water Day is celebrated every year on.:

(A) July 12 (B) May 22

(C) March 22 (D) June 24




Continue Reading →

Popular Posts

Recent Posts

Unordered List

Get daily update

Enter your email address Here:

Delivered by

Pages

Powered by Blogger.

Popular Music

Random Music

Disable context menu

Music Topic

Popular Posts